Oscilloscope for Ham Radio: See Your SSB and CW Signal

A transmitter can look healthy on every meter and still sound bad. The power reading is fine, the SWR is low and yet the stations on the next frequency complain about splatter. The reason is that ordinary meters average. They cannot show what happens within a single syllable of speech or a single dot of Morse. An oscilloscope for ham radio can. It draws the voltage against time, so you can see the envelope of your SSB signal, the shape of your CW keying, the ripple on a power supply and the hum in a microphone line. This guide explains what an oscilloscope can show in a ham shack, how to connect it safely to the radio, what bandwidth you need, how to run the classic two-tone test and what the pictures mean.
What an Oscilloscope Shows That Meters Do Not
An oscilloscope plots a voltage on the vertical axis against time on the horizontal axis. A meter shows an average or a peak, and a scope shows the whole shape of the signal. That shape is where the faults are hiding. An SSB signal that is overdriven has a flat top, and you can see the flat top on the screen. A CW signal that is keyed too sharply has a rectangular shape that causes key clicks, and a signal with a rounded start and end is clean. A power supply that has ripple shows it as a wavy line. For a radio amateur, the scope is a tool for checking the quality of the signal that you put on the air, as well as for a general repair bench.
Which Oscilloscope Do You Need
The main question is bandwidth. A scope shows a sine wave accurately only when its bandwidth is well above the frequency of the signal. A common rule is to take a bandwidth of at least three to five times the highest frequency that you want to see. For HF work up to 30 MHz, that suggests 100 MHz, but a scope of 20 to 50 MHz still shows the envelope of an RF signal well, because you are looking at the outline of the signal and not at each cycle of the carrier. For audio and power supply checks, even a small scope is enough.
- Small digital pocket scope, 1 to 20 MHz. Good for audio, ripple and keying. Low cost and portable, but limited for RF.
- Entry-level bench digital scope, 50 to 100 MHz. Good for the SSB envelope, CW keying and general repair. The best value for a ham shack.
- Older analogue scope, 20 to 100 MHz. Shows the envelope in real time. Heavy, but inexpensive second-hand.
- Software or USB scope, varies. Fine for casual measurements, but check the real bandwidth and the input range.
Two more specifications matter. The first is the number of channels. Two channels let you compare the microphone signal with the RF envelope. The second is the vertical sensitivity and the maximum input voltage, which for safe use with a transmitter must be matched by the probe and the attenuator that you use. Always check the manual for the maximum input.
Connecting a Scope to a Transmitter Safely
This is the part that needs care. Transmitters produce high voltages on the antenna line, and most scope inputs are made for lower voltages. The voltage depends on the power and the load. Across a 50 ohm load, the peak-to-peak voltage is the square root of eight times the power times the load resistance, a result of the RMS relation between voltage and power, which for 50 ohms is the square root of 400 times the power. The table shows the values.
| Power into 50 ohms | RMS voltage | Peak-to-peak voltage |
|---|---|---|
| 5 W | 15.8 V | 44.7 V |
| 10 W | 22.4 V | 63.2 V |
| 50 W | 50 V | 141 V |
| 100 W | 70.7 V | 200 V |
| 200 W | 100 V | 283 V |
These values are for a continuous carrier, and the peak of a modulated SSB signal at the same PEP reaches the same level. A common scope probe set to the 10 times position takes up to 300 V on many models, and the input of the scope itself is rated lower, so a direct connection at 100 W is not wise. The safe way is not to connect the probe to the line at all, but to take a sample of the signal through one of three routes.
- A pickup loop. A small loop of wire near the transmitter’s output cable or the dummy load picks up a small part of the RF. It is the safest method, because the loop is not connected. Move it closer or further to set the amplitude.
- A resistive divider or an attenuator. A 20 dB or 30 dB attenuator in a coax tee takes the signal down to a level that the scope can accept, and it keeps the 50 ohm impedance. Check the power rating of the attenuator.
- A directional coupler or the sampling port of a wattmeter. Many line sections have an output for sampling, at a fixed attenuation.
Use a dummy load for the test, as in the guide to dummy loads, so that you do not radiate while you adjust. Keep the transmit time short and the power moderate. And observe the common rules of safety: never open a mains-powered unit with the scope connected unless you know what you are doing, and remember that the earth of the scope probe is connected to the mains earth, so a clip on a live chassis can cause a short.
The Two-Tone Test for SSB
The two-tone test is the standard way to check the linearity of an SSB transmitter. You feed two audio tones, for example 700 Hz and 1900 Hz, of equal amplitude into the microphone input, and watch the RF envelope on the scope. Many radios have a built-in two-tone generator in the menu. If you have none, a computer sound card with a free tone generator program gives the two tones, and the audio chain explanation in the guide to SSB audio settings helps with the levels.
- Set up. Connect the transmitter to a dummy load. Connect the scope through the pickup loop or attenuator, and set the time base to see a few cycles of the beat, about 0.5 ms per division.
- Apply the tones. Transmit with the two tones at a moderate level and look at the screen.
- Read the pattern. A clean two-tone envelope looks like a series of sine-shaped lobes, with the peaks and the points where the envelope goes to zero in a regular pattern. The shape is two tones adding and cancelling, which is a “string of sausages”.
- Increase the level. Raise the microphone gain or the tone level slowly. At some point, the peaks of the envelope start to flatten, which is clipping. That is the level where the transmitter or its driver reaches its limit.
- Set the gain just below flat-topping. This is the level to use for speech, with a small margin. It maximises the average power without distortion.
- Check the ALC. Watch the ALC meter of the radio. If the ALC acts strongly before the flat-topping, the drive is too high.
Flat-topped peaks on the scope mean distortion that spreads the signal over the neighbouring frequencies, which causes splatter. The guides on key clicks and splatter and on PEP and wattmeters explain why a clean envelope matters and why an average-reading wattmeter hides the problem.
Checking CW Keying
For CW, the scope shows the rise and fall of the carrier when you press the key. Send a string of dots at a moderate speed and set the time base to a few milliseconds per division. A well-shaped keying has a rise and fall time of a few milliseconds, which is long enough to keep the bandwidth narrow, but short enough to sound crisp. If the leading and trailing edges are almost vertical, the signal has key clicks, which are audible as sharp ticks on both sides of the frequency. If the edges are very slow, the dots become soft and hard to read at high speed. Some radios let you set the rise time in a menu, and a scope helps you find a good value. Look also for any glitches at the start of the dot, a sign of relay bounce or a software problem.
Other Uses in the Shack
- Power supply ripple. Connect the scope across the output of the supply, with the AC coupling, and look for ripple and for spikes from a switching supply. The guide on choosing a power supply explains why switching noise matters.
- Microphone and audio. Look at the audio signal from the microphone, the level of the sound card output and the hum from a ground loop.
- Digital mode audio. Check that the audio drive to the radio is not clipped when you run FT8 or other digital modes.
- Keyer and key line. View the key line voltage and the timing of a keyer, and check that a CAT or PTT line is clean.
- Repairs. Look for the presence of an oscillator, the shape of a clock signal or the level of a detector output.
Setting Up the Display
A few settings make the picture easy to read. Use the trigger on the channel that carries the signal, set to normal mode, so that the trace is steady. For the two-tone envelope, trigger on the audio signal if you have a second channel, since the beat then stays still. Choose the vertical scale so that the signal fills about two thirds of the screen, and avoid the extreme edges where the trace can be clipped by the scope itself. Use the AC coupling for audio and ripple measurements, and the DC coupling when you want to see the level. Take a photograph of the screen with your phone or save the screenshot if the scope can do it, and label it with the date and the settings of the radio. A collection of such pictures is a useful log of the health of your transmitter, and you will recognise a change at once.
Reading the Pictures: A Quick Guide
Learn a few typical images. A clean sine wave has a smooth, regular shape. A clipped wave has flat tops and bottoms. A signal with hum has a slow wave added to the fast one, at 50 or 60 hertz. A signal with RF in the audio shows a fuzzy trace, since the RF is picked up by the audio line. A signal that has a spiky waveform often has an unstable or poor supply. Keep a photograph of the screen of a good signal from your own radio, so that you have a reference to compare with after any change in the station. It is a cheap and effective way to catch problems early.
The Bottom Line
An oscilloscope shows the shape of your signal and lets you see the faults that meters hide: flat-topping on SSB, key clicks on CW, ripple on a supply and hum in the audio. A scope of 20 to 100 MHz is enough for a ham shack. Connect it to a transmitter by a pickup loop or an attenuator and use a dummy load, since direct connection at higher power can exceed the limits of the probe and the scope. Run the two-tone test, set the drive just below flat-topping, shape the CW keying and keep a reference picture. A short session with the scope can improve the sound of your signal more than a new microphone.
Frequently Asked Questions
What bandwidth does a scope need for ham radio?
For envelope checks on HF, 20 to 50 MHz is usable and 100 MHz is comfortable. For audio and power supply checks, a few megahertz is enough.
Can I connect a scope probe directly to my transmitter output?
Not at higher power. At 100 W into 50 ohms the signal is about 200 V peak to peak, which can exceed the rating of the probe and the scope. Use a pickup loop or an attenuator.
What is a two-tone test?
Two audio tones, such as 700 and 1900 Hz, are fed to the SSB transmitter, and the RF envelope is observed. It shows the level at which the transmitter starts to clip.
How do I see key clicks on a scope?
Send dots and look at the edges of the keyed carrier. Almost vertical edges mean key clicks, and edges of a few milliseconds give a clean, narrow signal.
Is an old analogue scope still useful?
Yes. An analogue scope of 20 to 100 MHz shows the envelope in real time and costs little second-hand. A digital scope offers storage and measurements.
Do I need a spectrum analyser as well?
A spectrum analyser shows the frequency content, such as harmonics and splatter, and a scope shows the shape in time. The two are complementary, but a scope is a good first step.