Lazy H Antenna: A Stacked Wire Array for HF Gain

Most wire antennas are easy and modest: a dipole or an inverted V gives a clean pattern and no gain. The Lazy H antenna is a step up that remains made of wire. It uses four half-wave pieces of wire, two at the top and two at the bottom, fed together so that they act as one array with a strong broadside lobe. Radio amateurs who work a single band from a fixed station, and who have two supports about a wavelength apart, find it one of the best ways to add several decibels without a rotator or a tower with a beam. This guide explains how the antenna works, what sizes it has on the popular HF bands, how to feed it, how high to put it and which mistakes spoil it.
What a Lazy H Antenna Is
The name comes from the shape. Seen from the front, two horizontal rows of wire are joined by a vertical line in the middle, which makes the letter H lying on its side, and the antenna is “lazy” because it is simple to understand. Each row is a collinear array of two half-wave elements in line, so each row is about one wavelength long, with its feedpoint at the centre where the two elements meet. The two rows are one half wavelength apart, one above the other, and they are fed in phase. The pattern is bidirectional and strongest at right angles to the plane of the wires, that is broadside. Compared with a single half-wave dipole, the usual figure for the array in free space is about 5 to 6 dB of gain, depending on the exact build. In practice you should think of it as “a bit more than one S-unit better in the favoured directions”, which is a big improvement for a few lengths of wire.
There are two ideas combined. Collinear elements put more wire in the same line, which narrows the pattern in the horizontal plane and adds gain. Stacking elements one above the other narrows the pattern in the vertical plane, which lowers the takeoff angle and adds more gain. The Lazy H does both, which is why it works well for DX on a single band. The price is size and the fact that it is a single-band antenna by design, although some owners use it on the second harmonic with care.
Dimensions for the Popular Bands
All sizes follow from the wavelength. A half-wave element is about 143 divided by the frequency in megahertz in metres, when you allow for the velocity factor of wire in air, and each row is two such elements. The vertical spacing is the same as the length of one element. The table shows approximate figures for a design frequency near the middle of each band. Treat them as a starting length, and cut the wire a little long so you can trim it.
| Band | One half-wave element | Width of one row | Spacing between rows | Lowest row above ground |
|---|---|---|---|---|
| 20 m (14.15 MHz) | about 10.1 m | about 20.2 m | about 10.1 m | 5 to 10 m |
| 17 m (18.1 MHz) | about 7.9 m | about 15.8 m | about 7.9 m | 4 to 8 m |
| 15 m (21.2 MHz) | about 6.7 m | about 13.5 m | about 6.7 m | 3.5 to 7 m |
| 12 m (24.95 MHz) | about 5.7 m | about 11.5 m | about 5.7 m | 3 to 6 m |
| 10 m (28.4 MHz) | about 5.0 m | about 10.1 m | about 5.0 m | 2.5 to 5 m |
The numbers show why the Lazy H is popular from 20 metres upwards: a 15 metre version is 13.5 metres wide and about 12 to 14 metres tall to the top row, which a garden with two masts can hold. On 40 metres the same design would need rows 40 metres wide and a top wire at 20 metres or more, so it is a project for a farm or a club field, not for a small plot. On 10 metres it is small enough to mount on a roof between two poles.
How the Antenna Is Fed
The key requirement is that the two rows are fed with equal current and in phase. The common way is a phasing line: an open-wire line, made of two parallel wires with spacers, runs vertically between the feedpoint of the top row and the feedpoint of the bottom row. It is connected straight, without a crossover, so both rows get the same polarity. The main feedline is attached to the middle of this vertical section, and the length of each half of the section is about a quarter wavelength when the rows are a half wavelength apart. This arrangement transforms the impedance seen at the feedpoints, so that the junction presents a convenient value to the feedline. Designs differ in the details, for instance in the impedance of the open-wire line and in whether a balun and coax or an open-wire feeder go to the shack, and published designs use computed values. If you can, follow a design that has been modelled for your band rather than inventing the numbers.
Because the array is balanced, an open-wire feeder to an antenna tuner is the simplest honest way to feed it, and a good tuner will cope with the range of impedance that the line produces. The comparison in ladder line versus coax shows why a balanced line loses little even when the SWR is high. If you prefer coax, a 1:1 current balun at the bottom of the phasing section and a short run of coax work too, but check the SWR across the band and be ready to trim the elements, because the feed system is sensitive to small errors.
Height Above Ground and Takeoff Angle
A horizontal antenna works well only if it is high in wavelengths. The height of the lower row matters most because it controls the ground reflection, and therefore the takeoff angle. A lower row of about a half wavelength or more above ground, together with the stacking, gives a low angle suitable for DX. The principle is the same as in the guide to antenna height and takeoff angle: at heights less than a quarter wavelength a horizontal wire radiates mainly upward, like an NVIS antenna, which is good for close contacts and poor for the far end of the world. In the Lazy H, the stacking helps, since the upper row is a further half wavelength up, but you should still raise the whole assembly as high as the supports allow. If the lower row can be only a quarter wavelength above ground, the array still works, with a higher takeoff angle, and it can be a fine choice for contacts at medium distance.
The supports should be tall enough for two rows. Many builders use two trees or two masts, with a rope and pulley at the top and the bottom of each support, so that the wire assembly can be lowered for adjustment. Use non-conductive rope between the wire ends and the support, and add an insulator at each end of each row. Fibre rope that does not stretch much holds the shape of the array better in the wind.
The Pattern and What It Means for Your Station
The Lazy H is bidirectional, with its main lobes at right angles to the wires. The lobes are narrow in the horizontal plane, typically about 40 to 50 degrees wide between the half-power points for the collinear rows, so the antenna “sees” only a part of the horizon. This is its strength and its limit. If your best targets lie along the broadside directions, the gain is a big advantage. If they lie off the ends of the wires, the antenna is deaf in those directions, since the pattern has deep nulls along the line of the wires. Before you build, draw a line on a map through your location at right angles to the planned wires and see which regions it points to. For a station in Europe, a wire running roughly north to south points the broadside lobes east and west, towards North America and Asia, which suits many contest and DX plans. A wire running east to west points them north and south. The guide to reading antenna patterns explains the terms of lobes, beamwidth and nulls used here.
You can also make a small rotatable version for 10 metres, but most Lazy H antennas are fixed. A fixed antenna is not a disadvantage if the contacts you want are in the lobes. A club that runs a station in a contest on one band often builds a Lazy H aimed at the multiplier-rich regions and relies on a second, wider antenna for the rest.
Building the Antenna Step by Step
- Choose the band and the direction. Pick the band that you use most and the directions that matter, and check that the supports are on a line at right angles to the targets.
- Cut the wire. Use copper-clad steel or hard-drawn copper wire that can carry its own weight over the span without stretching. Cut four elements about five per cent longer than the table, so that you can trim.
- Make the rows. At the centre of each row, join the inner ends of the two elements to a central insulator that takes the feedline connection. Seal the joints against water and give them mechanical strength, since the centre insulator carries the weight of the phasing line.
- Build the phasing section. Make a vertical open-wire line of the right length between the two central insulators. Keep the spacing between its wires constant with spacers.
- Raise the array. Pull the top and bottom rows up, with the phasing line hanging between their centres, and keep the line away from supports and metal. Keep all wires taut and symmetrical.
- Connect and measure. Attach the feedline, with a balun if you use coax, and measure the SWR and the resonance with an analyser, such as a NanoVNA. Trim the element ends symmetrically until the lowest SWR is in the part of the band you use most.
- Check the pattern. Compare reports for the same stations on the Lazy H and on your previous antenna, and listen on the noise floor on the broadside and the end directions.
Common Problems and How to Avoid Them
The most frequent fault is an unequal feed between the two rows, usually caused by a twist in the phasing line, which puts the rows out of phase and ruins the gain. A crossover in the vertical line reverses the phase of one row, and the pattern then changes to a different shape with much less broadside gain, so check the line carefully. A second fault is an asymmetrical array: if one half is longer than the other, the feedpoint impedance and the pattern shift. Measure each element. A third is a phasing line that is too near a support or a metal mast, which detunes it. Keep it at least a metre away from conductive objects. A fourth is expecting performance on bands that the design does not cover. The array is cut for one band, and on others it gives a different pattern and an impedance that is hard to match.
The wind loads on a Lazy H are also real. Four long wires and a phasing line move in a storm, and rope, pulleys and insulators must be able to take the strain. Use a rope with a margin of strength, and avoid a design that depends on a single tie of the wire. Mind the safety of anything that hangs over a path or a road. The text on masts and guying covers the principles for putting wire antennas up safely.
Lazy H Compared With Other Options
If you want gain on one band from wire, the Lazy H competes with the collinear family and with the extended double Zepp, which is a single row of the same idea and gives about 3 dB. The Lazy H adds a second row for another 3 dB or so, at the cost of a second supported wire. A stacked Yagi pair gives more gain and can be turned, but it needs a tower and a rotator. A four-square gives gain and switchable directions with verticals, as in the guide to the four-square vertical array. Compared with a simple dipole at the same height, the Lazy H is the most economical way to a clear gain figure when you have the space, and it can be built for the price of the wire, rope and a few insulators.
Using the Antenna in Practice
A fixed bidirectional antenna changes how you operate. Plan the day around the directions that the antenna favours and the times when those paths are open. For a European station with the wires running north to south, the early evening on 20 metres opens the path to North America through the eastern lobe, and the morning opens Asia through the western lobe. Combined with a way to hear when a wanted station appears, such as spots from a DX cluster, you can leave the antenna to do its work and move to the band when the opportunity opens. Compare a signal report from a distant station with the same station on your usual dipole. Even a small improvement in reports is useful to confirm that the array is phased and tuned. Keep a log of the findings so you can see how the antenna performs across a season.
The Bottom Line
The Lazy H antenna is a stacked, collinear wire array for a single HF band, with two rows of two half-wave elements, about a half wavelength apart and fed in phase. It gives roughly 5 to 6 dB over a dipole, a bidirectional broadside pattern and a lower takeoff angle, for the cost of wire and rope. It needs two good supports, careful symmetry, a straight phasing line without a crossover and as much height as you can manage. It suits stations that work one band hard and have the contacts they want in the broadside directions, and it rewards patience in the build with a gain that few wire antennas can match.
Frequently Asked Questions
How much gain does a Lazy H antenna have?
About 5 to 6 dB over a half-wave dipole in free space for a well-built array, from the collinear rows and the stacking together. Ground effects can add or remove a little.
Is a Lazy H a multiband antenna?
No, it is designed for one band. It can radiate on other bands, but the pattern and the impedance change and the gain is not predictable without modelling.
What is the best height for a Lazy H antenna?
As high as you can get it, with the lower row at least a quarter wavelength above ground and ideally about a half wavelength, so that the takeoff angle is low enough for DX.
Can I feed a Lazy H with coax?
Yes, with a 1:1 current balun at the bottom of the phasing section, but an open-wire feeder and a tuner is simpler for a balanced array and loses little. Check the SWR and trim the wires after installation.
Which direction does a Lazy H radiate?
Broadside, which means at right angles to the line of the wires, in two opposite directions. Along the wires there are deep nulls, so choose the orientation with a map before you build.
Why is it called a Lazy H?
Because of its shape: two horizontal rows of wire joined in the centre by a vertical line look like the letter H on its side, and the antenna is simple enough to describe as lazy.