Linked Dipole Antenna: A Light Multiband Wire for Portable Operating

Linked Dipole Antenna: A Light Multiband Wire for Portable Operating

On a summit, in a park or at a campsite, the best antenna is the one that you can put up in ten minutes and take down in five. A single dipole cut for one band is light and efficient, but it covers only that band. A fan dipole covers several, but it needs several wires and a spreader. A trap dipole covers several, but its traps add weight and loss. The linked dipole antenna takes a simpler route: one wire per leg, with breaks at the points where the wire would be cut for each band, and small links that close the breaks. Close all the links and you have the lowest band; open the outer ones and the antenna is shorter, for a higher band. It is a favourite of operators on Summits on the Air and Parks on the Air, because it has a very good efficiency for its weight and almost nothing to go wrong. This guide shows how it works, how to calculate the lengths, which hardware to use and how to set it up in the field.

How a Linked Dipole Works

A half-wave dipole is resonant when its two legs together are about a half wavelength long. For a different band, you need a different length. A linked dipole has each leg made of several sections of wire. The first section, from the feed point, is the length of one leg for the highest band. At its end there is a link, a small connector that can join it to the next section or leave it open. The next section adds the extra length for the next band down, and so on. On the highest band, you open the first link, so the current flows only in the first section, and the rest of the wire hangs unused beyond the open link. On the next band, you close the first link and open the second. For the lowest band, you close all the links.

The antenna is therefore a plain dipole on every band, with the advantages that this implies: a feed impedance close to 50 ohms when it is high enough, a bidirectional pattern and simplicity. No coil or trap loss is added, since the antenna is a single continuous wire when the right links are closed. The article on the first HF antenna explains the properties of a dipole, and the guide to the inverted V shows the shape that most portable users choose, with the centre on a mast and the ends sloping down.

Calculating the Lengths

For a bare or insulated wire dipole in the field, a good starting formula is that the total length in metres is about 142.5 divided by the frequency in megahertz, which includes the typical shortening of a wire antenna. The length of each leg is half of that. The table shows a set for the common bands, with the frequencies chosen in the middle of the part of the band that most operators use. The last column gives the extra wire to add for each lower band.

BandDesign frequencyLeg length from the feed pointExtra section to add
10 m28.4 MHz2.51 mfirst section
12 m24.94 MHz2.86 m0.35 m
15 m21.2 MHz3.36 m0.50 m
17 m18.1 MHz3.94 m0.58 m
20 m14.2 MHz5.02 m1.08 m
30 m10.12 MHz7.04 m2.02 m
40 m7.1 MHz10.04 m3.00 m

These are starting values, and the final lengths are found by testing, because the height above ground, the type of insulation, the bend of the wire and the surroundings all change the resonance. A common method is to cut each section a little long, then shorten it while measuring the SWR with an antenna analyzer at the working height. Shortening is easy, and lengthening is not, which is why you begin with a surplus. Mark the sections with the band name on a piece of tape or a heat-shrink label, so that you do not need to measure in the field. If you plan to use only four bands, such as 40, 30, 20 and 17 metres, you need only four sections per leg.

Testing and Trimming at Home

Build the antenna on a quiet day at home, and test it in the way that you will use it. Raise the centre to the height of your usual mast, spread the legs in an inverted V and connect an antenna analyzer or a NanoVNA at the feed point, as the article on the NanoVNA explains. Start with the highest band. Set the links for that band, sweep the band and note the frequency at which the SWR is lowest. If it is below your target, the wire is too long, so trim a little from the end of the outermost section in use, equally from both legs. Repeat until the minimum sits where you want it. Then close the first link, open the second and do the same for the next band, trimming only the new section. Working from the highest band to the lowest, each trim affects only its own band. Write the final lengths on the labels. In the field, the height will differ, so expect the resonance to move by a few percent, and accept a small residual SWR. A well-trimmed antenna with a choke balun usually gives an SWR below 1.5 across the part of the band that you use most.

Links and Hardware

The link is the part of the antenna that most invites ingenuity. Requirements are modest: a secure electrical contact that survives the weather, a small mass and quick operation. Several solutions are in common use.

  • Banana plugs and sockets. A pair of insulated sockets on the ends of two sections, joined by a short plug, makes a neat link. They are cheap and easy to fit.
  • Powerpole connectors. Standard two-way connectors can serve as links, and they are robust and recognisable. The article on Anderson Powerpole connectors shows the crimping method.
  • Crocodile clips or small bolted terminals. They are quick and cheap, and they work well as long as they are tightly closed.
  • Soldered loops with a carabiner or a short jumper. The most compact of all, but they need care.

Whichever type you choose, make the joints strong, because the wire is under tension from the supports and the weight of the sections. Take a little slack in the wire into the link, so that the pull is carried by the insulator or by a loop of cord and not by the electrical contact. Seal the connectors against moisture if you plan to leave the antenna up for days, and keep a spare link or two in the bag.

Wire, Insulators and Weight

The wire should be light and strong. A stranded copper-clad steel wire, insulated, of about 0.5 to 1 millimetre in diameter, balances weight, strength and loss. Very thin wire has a higher resistance and a lower bandwidth, and thick wire is heavy and kinks. The article on HF antenna wire compares the options. Use light insulators or tie the ends of the wire to loops of cord, and make the cord long enough to reach a branch or a pole. The finished antenna, with a 40 metre version, weighs a few hundred grams and packs into a small bag, with the wire on a winder or a piece of card. The winding method makes a difference: label each winder with the band and wind each section separately to avoid tangles.

Feeding the Antenna

Feed the antenna with coax at the centre, through a 1:1 current balun or at least a choke made of a few turns of the coax on a ferrite core. A choke prevents current on the outside of the coax, which would distort the pattern and bring RF into the shack. The article on baluns and ununs explains the difference. Use a light coax such as RG-174 or a thin low-loss type for QRP power, and a slightly larger type for 100 watts, remembering that thin coax has more loss on the higher bands. Keep the feedline short, as it adds weight and loss, and fix the centre of the antenna to the top of a mast with a strong, light clip.

Setting Up in the Field

  1. Choose the band for the time of day and the path, then close and open the links accordingly before you raise the antenna. It is easier on the ground than at the top of a pole.
  2. Attach the centre to the mast. A telescopic fibreglass pole of 6 to 10 metres is the usual support. The guide to push-up masts and guying shows how to secure it.
  3. Spread the legs in an inverted V, with the ends at least a few metres from the ground and away from people. Tie them to stakes or trees with cord.
  4. Connect the coax and check the SWR. If it is high, check the links first, since a loose link is the common fault.
  5. To change band, lower the antenna or, if the links are within reach, open and close them with a hook, or lower the mast partly.

Changing band takes a few minutes. This is the main drawback of the linked dipole: you cannot switch bands from the chair. For operators who work one or two bands in a session, as on a summit with a plan of operation, this hardly matters. Those who want to hop between bands often might prefer a fan dipole or a trap dipole, compared in the articles on the fan dipole and the trap dipole.

Choosing the Bands for Your Plan

You do not need to build all seven bands. Think about where and when you operate. A summit activator in winter often uses 40 and 20 metres, with 30 metres for CW and a higher band when the sunspots help. A park activator with a daytime plan might use 20, 17 and 15 metres. A QRP operator who likes the low bands at dusk adds 40 and 30 metres. Every added band adds a link and a section to each leg, and with them weight, a little complexity and a few more places for a fault. A set of four bands is a good compromise. For the bands themselves, the guides to the 20 metre band and the 40 metre band explain which hours and conditions suit each one, so that you choose the wire for the time of day.

Strengths and Weaknesses

  • Efficiency. On each band the antenna is a full-size dipole with no traps or coils, which gives the best performance for a wire of its weight.
  • Light and cheap. The cost is wire, a few connectors and some cord.
  • No tuner needed. A well-cut dipole shows a low SWR on the band and works directly with a QRP radio that has no tuner.
  • Manual band change. It needs a few minutes and sometimes lowering the antenna.
  • Dangling sections. The unused sections beyond an open link hang from the antenna and can slightly alter the resonance. Cut the lengths by testing in the same condition in which you will use them.
  • Single-band at a time. Only one band is available in a configuration, while a fan dipole lets you switch by changing the frequency alone.

The Bottom Line

A linked dipole antenna is a wire dipole whose legs are made of sections joined by links, so that opening the outer links shortens it for a higher band. Using a total length of about 142.5 divided by the frequency in MHz, the legs are 10.04 m on 40 metres, 5.02 m on 20 metres and 2.51 m on 10 metres, with extra sections added for each lower band. It is light, efficient and simple, it needs a choke balun and a light mast, and it fits SOTA and POTA work, where a few bands are used in a session. Cut each section long, trim it with an analyzer, label the sections and keep spare links, and the antenna will serve for years.

Frequently Asked Questions

How does a linked dipole change bands?

You open or close links between wire sections. With all links closed the antenna is at its longest for the lowest band, and with the outer ones open it is shorter for a higher band.

What length is each leg on 20 metres?

About 5.0 metres per leg, or 10.0 metres in total, at a design frequency of 14.2 MHz. Trim it with an analyzer for your height and wire.

Do I need an antenna tuner?

Usually not. A correctly cut dipole has a low SWR on the band. A tuner may help if you want to use a wider range of a band.

What do I use for the links?

Banana plugs, Powerpole connectors, small bolted terminals or crocodile clips. Choose one that is secure, light and weatherproof.

Can I change band without lowering the antenna?

It depends on how high the links are. Many operators lower the antenna or the mast to change the links, which takes a few minutes.

Is a linked dipole better than a fan dipole?

For efficiency and weight it is excellent, but changing band is slower. A fan dipole is easier to switch, but has more wire and more interaction between bands.


By the team behind LY4A

More tools from our team

LY4A is made by Internet Solutions. Try the rest of our products — each one saves you time in a different way.

internet-solutions.net ↗
Social media auto-posting PostRSS New posts from your RSS feed go to Facebook, X, LinkedIn, Telegram and 60+ more networks automatically. For clubs: DX news and club bulletins straight to Facebook and Telegram Free plan · since 2014 AI live chat for websites Talkmio Your website answers visitors 24/7 from your own content, in their language. For ham shops and clubs: questions answered 24/7, even during a contest Free plan · no card needed AI assistant Ask Mio Chat, code, design, writing and research. Mio picks the best model for each task. Antenna maths, QSL card designs, contest rules explained in plain words Free plan AI blog & social autopilot AI Blog Autopilot AI writes 2,000–3,000-word SEO articles and shares each one to 58+ social networks. For club websites: regular articles written for you and shared to social networks First 3 articles free Website health check Site AI Audit SEO, speed, SSL, security and e-mail setup in one report, ranked by what to fix first. Check your club or DXpedition website for free First audit free Deep SEO crawl Site SEO AI Audit A full SEO crawl across 7 areas, including AI search visibility, with fixes ranked by impact. See why your club site is not found on Google — and how to fix it First audit free RSS & product feeds RSS Feed Creator Create RSS from any web page, plus product feeds for Google and Meta that update themselves. Follow DXpedition and club pages that have no RSS Free plan Web development & SEO Internet Solutions Websites, e-shops and custom systems, designed, built and run by our team. Club websites, DXpedition pages, log search and QSL systems Since 2011