Crimp Coax Connectors: BNC, N and PL-259 Done Right

Almost every radio amateur learns to solder a PL-259 plug, and many remain loyal to it for life. Yet the connectors that go on commercial cables, on the cables of test equipment and on much of the coax in a professional installation are crimped, and a good crimp is as reliable as a good solder joint, faster to make and kinder to the cable. The trick is that a crimp works only when every detail is right: the right connector for the cable, the right die in the right tool, the right strip lengths and the right order of steps. A wrong die or an extra millimetre of stripped dielectric turns a quick job into an intermittent fault. This guide explains how to crimp coax connectors, with BNC and N types as the main examples, what tools you need, how to prepare the cable, how to test the result and which mistakes to avoid.
Why Crimp Instead of Solder
Soldering uses heat, which can melt the dielectric of the cable and distort the centre conductor, particularly with foam-filled coax and thin cables. It needs practice to avoid cold joints and to prevent solder from running along the braid and stiffening it. Crimping is a mechanical joint, made by deforming the metal of a ferrule or a pin around the conductor until the two form a gas-tight contact. Done with the correct tool, it is repeatable, fast and consistent, and a technician can make dozens of identical connections in an hour. The mechanics of crimping are explained in the article on the crimp joint. For radio use up to the UHF range, a well-made crimp has low resistance and a stable impedance, and for the higher microwave bands good connectors are made with the same methods.
There are still cases in which soldering is the better choice. The classic PL-259, also called the UHF connector, is designed to be soldered at the shell, and crimp versions are not common for it, though they exist. The article on how to solder a PL-259 describes the method. For BNC and N connectors on RG-58 and similar cables, crimp types are the norm, and the following sections apply to them. The details of the connector families themselves are in the guide to RF connectors.
Match the Connector to the Cable
The first rule of crimping is that the connector must be made for the exact cable. A coaxial cable has an outer diameter, a braid and a dielectric that differ between types. RG-58, RG-59, RG-8X, RG-213, LMR-240 and LMR-400 are all different, and a connector for one will not fit another. The packaging of a crimp connector says which cable it fits, and the part number includes the cable family. The comparison in the article on coaxial cable for ham radio helps to choose the cable first, and then the connector.
| Cable | Outer diameter | Typical connectors | Typical crimp die (hex) |
|---|---|---|---|
| RG-58 | about 5 mm | BNC, N, TNC | around 5.4 mm for the braid ferrule, 1.7 mm for the pin |
| RG-8X | about 6 mm | N, PL-259 with adapter | die size from the connector maker |
| RG-213 | about 10 mm | N, PL-259 | about 10 to 11 mm for the ferrule |
| LMR-400 style | about 10 mm | N, PL-259 | maker’s die, usually for the outer ferrule and the pin |
The sizes in the table are only a guide. Each connector maker publishes the exact die size and the strip dimensions for its parts, and those figures are the ones to follow. If the packet has no instructions, look up the part number on the maker’s page before you cut the cable.
Tools You Need
- A crimp tool with interchangeable dies, usually hexagonal, for coax connectors. A ratcheting tool gives a repeatable force and does not release until the crimp is complete.
- The right dies, or a tool made for the cable family. One die crimps the centre pin, and a larger one crimps the outer ferrule.
- A coax stripper set for the cable, or a sharp knife and a ruler. A stripper with adjustable blades makes clean cuts to a set depth.
- Cutters or a fine saw, for a square cut of the cable end.
- A multimeter with a continuity range, and, if you have one, an antenna analyzer or a NanoVNA, for testing.
- A hot-air gun and heat-shrink tubing, for the final weatherproofing.
A cheap, non-ratchet crimper, the type with a plain jaw, is a common cause of bad crimps. It does not bring the die to the full depth consistently, and the result is a loose joint that looks fine and fails in a month.
Preparing the Cable
Cut the cable end square with a clean cut. Slide any parts that go over the cable onto it first, in the correct order: the boot, if there is one, and the ferrule, a short metal sleeve that will be crimped over the braid. Forgetting to put the ferrule on before you strip the cable is the commonest mistake, and it means starting again. Strip the outer jacket to the length that the maker specifies, usually 10 to 15 millimetres for a BNC on RG-58, without nicking the braid. Fold the braid back over the jacket, or comb it out into a smooth cone if the design asks for it. Strip the dielectric to expose the centre conductor to the length that the pin needs, typically 3 to 5 millimetres, and do not cut into the centre conductor. Remove any loose braid strands, because a single strand that touches the centre conductor is a short circuit that will give you high SWR or no signal.
The Centre Pin
The centre pin is crimped with the small die. Slide the pin over the bare conductor until the end of the dielectric touches the shoulder of the pin, then crimp. The inspection hole in the barrel of the pin, if there is one, shows that the conductor has reached the end. Pull gently on the pin to check that it holds. A good crimp on the pin deforms it into a uniform hexagon and does not split it. For solid centre conductors, the crimp is a standard operation. For stranded conductors, make sure that every strand is inside the barrel, and twist the strands lightly before you slide it on. Some connectors have a solder pin, where a bead of solder through the hole adds security, but a crimp pin of good quality needs no solder.
The Outer Ferrule and the Braid
With the pin in place, push the body of the connector onto the cable. The dielectric goes inside the connector, the pin goes into the contact socket, and the braid slips over the rear sleeve of the body. The inner end of the dielectric should sit square against the body of the connector. Then slide the ferrule forward over the braid, so that the braid is trapped between the ferrule and the sleeve. Crimp the ferrule with the larger die, and keep the die square to the part. A hexagonal crimp should show six clean flats. Give the finished plug a firm pull in the axial direction, about the force of hanging a kilogram from it, and a twist. A well-made joint does not move. This is the pull test that professionals use, and it takes five seconds.
Checking the Result
A visual check comes first: the ferrule should be uniform, the cable should enter straight and no braid strands should stick out. Then use the multimeter. Check that the centre pin and the shell are not connected, which would be a short, and that the centre pin at one end is connected to the centre pin at the other, and the shell at one end to the shell at the other. For a better test, connect the cable to an antenna analyzer or a NanoVNA with a dummy load at the far end and look at the return loss or the SWR. A good coax assembly shows an SWR close to 1:1 up to the frequencies you use. The method is described in the article on coax fault finding, and the same tools that find faults in an old cable prove that a new one is good.
Common Crimping Mistakes
- The wrong die. A die that is too large leaves a loose crimp, and a die that is too small crushes the cable and changes its impedance.
- Too much dielectric stripped. This leaves an air gap and a change in impedance, and the connector may not seat.
- Too little braid under the ferrule. The mechanical grip is weak and the shield is poor. Use all of the braid.
- Stray strands. One strand of braid touching the pin gives a short.
- A crooked cut. The cable does not seat evenly, and the stress shows at the connector.
- Forgetting the boot or ferrule. It cannot be added afterwards.
- Skipping the weatherproofing. Water gets in, as the article on weatherproof connectors warns, and a good crimp is wasted.
Practise on Scrap Cable First
The first crimp is rarely the best one, and a connector costs a few coins, so practise on short offcuts. Make three or four joints, then cut each one open with a knife and look inside. A good joint shows the braid pressed evenly between the ferrule and the sleeve, a pin that is fully on the conductor and a dielectric that meets the body square. The faults that you see in the cut-open samples, a gap, a strand or a half-seated pin, are the ones that would have failed on the mast. This habit is also the best way to learn the effect of the die size, since you can compare a crimp made with the right die and a crimp made with a slightly wrong one and see the difference directly. After this exercise you will make the joints on the real cable with confidence.
Crimp, Solder or Compression?
A third family of connectors uses compression: a ring or a sleeve is pushed along the connector with a special tool and grips the cable evenly. Compression connectors are common on cable television and satellite cables, and they are used for some low-loss cables at VHF and UHF. They are quick to fit and weatherproof by design, but need the right tool for each cable. For HF work, where the power can reach a kilowatt, a well-soldered PL-259 or a quality N connector is the usual choice. For VHF, UHF and test leads, crimped BNC and N connectors dominate. The rule that applies to all three is the same: use the connector, the tool and the dimensions that the maker specifies for the cable you have.
Weatherproofing and Strain Relief
An indoor connector, such as a BNC at the back of a radio, needs only a boot or heat-shrink for strain relief. An outdoor connection needs more. Slide a piece of adhesive-lined heat-shrink tubing over the cable before you fit the connector, and shrink it over the joint when the connector is mated, so that the cable entry is sealed. Cover the whole connection with self-amalgamating tape or mastic and a layer of vinyl tape, and form a drip loop so that water runs off the cable before it reaches the connector. Mate the connectors fully and avoid pulling on the cable, because the crimp is strong in tension but a pull at an angle stresses the contact.
The Bottom Line
To crimp coax connectors well, choose a connector made for your exact cable, use a ratcheting crimp tool with the right dies, slide the ferrule and boot onto the cable first, strip the jacket, braid and dielectric to the maker’s lengths, crimp the centre pin and then the outer ferrule, pull test the joint and check it with a meter or an analyzer. Avoid a wrong die, stray braid strands and too much stripped dielectric, and finish outdoor connections with heat-shrink and tape. Practised once or twice on scrap cable, the method gives joints that match the best soldering, in a fraction of the time, with little risk to the cable.
Frequently Asked Questions
Is a crimped connector as good as a soldered one?
Yes, when it is made with the right connector, tool and die. It offers a gas-tight joint with low resistance and consistent results.
Can I crimp a PL-259?
Crimp versions exist, but the classic PL-259 is designed to be soldered. Use a crimp type made for your cable if you want to crimp.
How do I know which die to use?
Follow the connector maker’s data sheet, which gives the die size for the pin and the ferrule for each cable type.
Why does my crimped BNC give a high SWR?
Typical causes are a stray braid strand touching the pin, too much stripped dielectric or a wrong crimp. Check with a continuity test and a sweep.
How hard should I pull to test a crimp?
Give it a firm pull of about the weight of a kilogram and a twist. A good joint will not move.
Do I need heat-shrink on a crimped connector?
For outdoor use, yes. Adhesive-lined heat-shrink and tape keep water out of the cable and connector.