Near Field and Far Field: Where an Antenna’s Fields Change Character

The difference between the near field and far field of an antenna explains a surprising number of everyday puzzles. An antenna does not simply push a wave into space. Close to the wire, the electric and magnetic fields are tangled, they store energy and give it back, and their behaviour depends on the shape of the antenna. Far away, the fields settle into the clean, orderly wave that textbooks draw. The boundary is not a sharp line, but knowing roughly where it lies shows why a small loop is quiet on a noisy day, why a ferrite on a cable cures an interference problem that a metre of distance does not, why antenna gain cannot be measured from close by and why the rules for RF exposure change with distance. This guide uses plain language and the distances that matter on the amateur bands.
Three Regions Around an Antenna
Engineers divide the space around an antenna into three regions, as described in the article on near and far field. They are not separated by walls, but their character is different.
- The reactive near field is the region closest to the antenna. The electric and magnetic fields are out of phase, and a large part of the energy sloshes back and forth between the antenna and the space around it, in the way that energy moves between a coil and a capacitor. Only a part of it becomes radiation. The reactive region extends to a distance of about one sixth of a wavelength, more exactly lambda divided by two pi, for small antennas.
- The radiating near field, also called the Fresnel region, lies beyond. The fields radiate, but the shape of the pattern still changes with distance, since the waves from different parts of the antenna have not yet combined into a single clean front. For large antennas this region can extend a long way.
- The far field, or the Fraunhofer region, begins where the pattern no longer changes with distance, and only its strength falls, in proportion to the inverse of the distance. In this region the electric and magnetic fields are in phase, at right angles to each other and to the direction of travel, and their ratio has a fixed value: the impedance of free space, about 377 ohms.
Where the Boundaries Lie
For a small antenna, one that is short in comparison with the wavelength, the far field starts at a distance of a few wavelengths. For a large antenna, such as a long Yagi, a dish or an array, the relevant distance is the Fraunhofer distance, which is two times the square of the largest dimension of the antenna divided by the wavelength. It is the distance at which the difference in path length from the two ends of the antenna to the observer is less than a small fraction of a wavelength, so that the waves add as if they came from one point. The idea is explained in the article on the Fraunhofer distance. A few examples with numbers show the scale.
| Antenna | Wavelength | Largest size | Reactive limit (about lambda / 6) | Far field starts at (2D squared / lambda) |
|---|---|---|---|---|
| Dipole on 14 MHz | 21.4 m | 10 m | 3.4 m | about 10 m |
| Dipole on 3.7 MHz | 81 m | 38 m | 13 m | about 36 m |
| 3 m boom Yagi on 144 MHz | 2.08 m | 3 m | 0.3 m | about 8.7 m |
| Small loop on 7 MHz | 42.8 m | 1 m | 6.8 m | few metres (the reactive limit) |
| 1 m dish on 10 GHz | 0.03 m | 1 m | 0.005 m | about 67 m |
The figures show two things. On HF, the near field of an antenna fills the garden and the neighbouring houses, since a wavelength is tens of metres. On microwaves, a dish has a near field of tens of metres even though the wavelength is a few centimetres, because the dish is many wavelengths across. That is why antenna ranges for microwave dishes need a distance of many metres.
How the Fields Differ
In the far field, the electric and magnetic parts are tied together by the impedance of free space, and measuring one gives the other. In the reactive near field, there is no fixed ratio. A short dipole or a vertical whip produces a near field in which the electric component is much larger than the magnetic one, a high-impedance field. A small loop produces the opposite, a field in which the magnetic part dominates, a low-impedance one. The shape of the antenna decides which kind you meet. This difference is the key to several practical effects.
Why a Small Loop Hears Less Noise
Much of the man-made noise on the lower bands comes from sources close to the receiving antenna, such as switching power supplies, lamp dimmers, chargers and power lines. At the distance of a few metres, the noise from a small source is in the near field, and the near field of most electrical devices is dominated by the electric component. A small receiving loop responds mainly to the magnetic field, so it is less sensitive to this local electric noise. It picks up the distant signals, which arrive as a far-field wave with both components, as well as it does anything else. This is why a small magnetic loop, such as those in the article on magnetic loops for apartments, can have a better signal-to-noise ratio than a full-size wire on a noisy day, even if its output is much lower. The same idea underlies the loops used for receiving on the low bands, covered in the article on low-band receive antennas.
The effect is the reason why you hear a change when you move a receiving antenna by a metre or two. In the near field of a noise source, small changes in distance cause big changes in the signal, and the field falls much faster than in the far field, with the inverse cube of the distance for a magnetic dipole field. A few metres of separation between the noise source and the receiving antenna therefore bring a large improvement.
Coupling Between Antennas and Cables
The near field is also where antennas and cables interact. Two antennas on the same tower or on adjacent masts are inside each other’s near fields, and they couple, change each other’s patterns and impedances and sometimes absorb power from each other. The article on antenna interaction on a tower describes the spacing needed to reduce this effect. The same coupling explains why a cable running near a transmitting antenna picks up RF, why a feedline that runs parallel to a dipole carries common-mode current and why a metal gutter or a fence close to the antenna detunes it. At the distances typical for a garden, many objects are in the reactive near field of an HF antenna.
RF Exposure and the Near Field
The distinction matters for safety. Exposure limits are given in terms of the electric field strength, the magnetic field strength or the power density. In the far field, the three are linked, so it is enough to compute the power density from the transmitter power and the antenna gain. In the near field they are not linked, and the simple formula can underestimate or overestimate the field. Close to the antenna, the electric and magnetic fields must be evaluated separately, either by measurement or by a computer model. The article on RF exposure safety explains the practical approach: keep antennas away from places where people stay, use the calculators that include the near-field correction and favour caution for low-band antennas that are close to the house.
Measuring Antennas and Pattern Tests
A pattern measurement or a gain comparison is valid only if it is made in the far field. If a receiving probe is too close to a large antenna, the readings contain the near-field effects, and the pattern seems to have filled-in nulls and a wrong gain. For amateur use, the rule of two times the square of the dimension divided by the wavelength gives the minimum distance. For a 3 m Yagi on 144 MHz, 9 metres is enough. For a large HF beam, the distance is tens of metres, and a drone or a distant field strength meter is the usual way. The same applies when you check a pattern with a second antenna, as in the article on the radiation pattern: keep the test antenna beyond the far-field distance, and keep it away from the ground and from metal.
Rules of Thumb for the Garden Station
A few practical rules follow from all this, and they cost nothing to apply. First, treat every object within about a sixth of a wavelength of an antenna as part of it: a metal gutter, a wire fence, a downpipe or the coax itself can change the impedance and the pattern. On 7 MHz this distance is about 7 metres, so most of a small garden qualifies. Second, route the feedline away from the antenna at a right angle for as far as you can, so that it leaves the strongest part of the near field quickly. Third, when you chase noise, move the receiving antenna, a portable receiver or a loop, and listen for the sharp change that signals a near-field source. Fourth, when you compare two antennas, keep both away from large metal objects and well apart from each other, because they couple. Fifth, when you plan an installation near people, imagine a sphere around the antenna in which the field is highest, and keep it clear.
Radiating Near Field of a Yagi
A long Yagi gives a good picture of the radiating near field. On 144 MHz a 6 m boom has a far-field distance of 2 times 36 divided by 2.08, which is about 35 metres. Inside that distance the pattern depends on where you stand. Close to the beam, on the axis, the field is not yet focused, and the gain you would measure with a probe is below the real one. At 35 metres or more, the main lobe has formed and the gain is as published. It is why a test of a large antenna in a small garden is misleading, and why two operators who measure the same beam at different distances can obtain different numbers without either being wrong.
What the Free-Space Impedance Means
The number 377 ohms, the impedance of free space, appears in far-field calculations. If you measure the electric field in volts per metre, the power density in watts per square metre is the square of the field divided by 377. This is how field strength meters and exposure calculators relate the two quantities. In the far field you can use it with confidence, and in the near field you must not. For link calculations between stations, which are in the far field of each other, the formulas of the article on free-space path loss apply from the start.
The Bottom Line
An antenna has a reactive near field within about one sixth of a wavelength, a radiating near field beyond it and a far field that begins at a few wavelengths for small antennas, and at two times the square of the antenna size divided by the wavelength for large ones. In the far field the fields are in phase and linked by 377 ohms, while in the near field they are not. This explains why small loops reject local electrical noise, why antennas and cables interact at short distances, why exposure calculations need care near the antenna and why patterns must be measured far enough away. On HF, your whole garden is within the near field, so spacing, separation and measurement all deserve a little thought.
Frequently Asked Questions
Where does the far field begin?
For small antennas at a few wavelengths, and for large antennas at the Fraunhofer distance, two times the square of the largest dimension divided by the wavelength.
Why is a small loop quieter than a dipole on a noisy day?
It responds mainly to the magnetic field, and most local noise sources have a dominant electric near field, so the loop picks up less of it while still hearing the distant signals.
Is the near field dangerous?
It is where the strongest fields are, so exposure limits apply there with extra care. Keep antennas away from where people spend time and evaluate the electric and magnetic fields separately.
Why can’t I measure antenna gain from a short distance?
The near-field effects distort the readings. The measurement must be made beyond the far-field distance for the antenna you are testing.
What is the 377 ohm number?
The impedance of free space, the ratio of the electric to the magnetic field in a far-field wave. It links field strength to power density.
Why does moving a receiving antenna a metre change the noise?
Noise sources close by are in the near field, where the field falls very quickly with distance, so a small move makes a large difference.