Grid Dip Meter: Find Resonance of Antennas, Traps and Coils

Grid Dip Meter: Find Resonance of Antennas, Traps and Coils

Some of the most useful instruments on a ham radio bench are very simple. The grid dip meter, also called a dip meter or a dip oscillator, is one of them. It is a small tunable oscillator with a meter. Hold its coil near a tuned circuit that is not powered, turn the dial, and when the oscillator frequency matches the resonant frequency of the circuit, the meter needle dips. The dial then shows the frequency. With this one tool you can check a trap before you hang it in a tree, find the resonance of a coil and a capacitor, measure the length of a coax stub, see where a wire antenna is resonant and use the instrument as a simple signal source or a wavemeter. This guide explains how the tool works, how to use it correctly and where modern analysers have taken its place.

How a Dip Meter Works

A grid dip oscillator is an oscillator whose frequency is set by a tuning capacitor and a plug-in coil, which together form an LC circuit. The meter measures the oscillator’s drive current, originally the grid current of a vacuum tube, which is the origin of the name, and in modern solid-state versions the current of a transistor. When the oscillator coil is brought close to another resonant circuit and the oscillator frequency is tuned to the resonant frequency of that circuit, the second circuit absorbs energy from the oscillator. The oscillator is loaded, its drive current falls, and the meter shows a dip. The dial of the oscillator, which is calibrated in frequency, tells you at which frequency the dip occurred, and so the resonant frequency of the circuit.

The principle is the same as the coupling between any two tuned circuits. The coupling is magnetic, through the coils, so the tool works with circuits that have a coil or a loop that you can approach. A circuit that is not powered is a better target than one that is working, because the signals in a working circuit confuse the measurement. This is why the tool is used for things on the bench and for antennas that are disconnected from the radio.

What You Can Measure

  • Traps. A trap is a parallel resonant circuit in a trap dipole. A dip meter tells you its resonant frequency before you install it, so that you can adjust the coil or the capacitor, as the guide to trap dipole antennas explains.
  • Coils and capacitors. Connect a coil to a capacitor of known value, find the resonant frequency and calculate the inductance. The reverse also works: if the coil is known, you can find an unknown capacitance.
  • Antennas. A wire antenna is resonant at some frequency. Couple the dip meter loosely to the feedpoint, through a small loop, and find the dip. It tells you where the antenna is resonant without a transmitter.
  • Coax stubs and cable length. A section of coax is a resonant line at the frequency where its length is a quarter or half wavelength. A dip meter can find that frequency, which gives you the velocity factor of the cable, as the articles on velocity factor and coax stubs describe.
  • Filters and matching networks. An L-network or a tuned circuit built for a given band can be checked on the bench, before you put it on the air.
  • As an absorption wavemeter. With the oscillator off, the instrument works as a passive detector: tune the circuit, and a dip or a rise in the meter shows that a nearby transmitter is radiating at that frequency.
  • As a signal source. The oscillator can serve as a rough generator for aligning a receiver or a filter.

Using the Tool Step by Step

  1. Choose the coil. The instrument comes with a set of plug-in coils for different frequency ranges. Select the coil whose range includes the expected frequency, since the dial is calibrated for each coil.
  2. Switch on and adjust. Turn on the oscillator and set the sensitivity control, if any, so that the meter reads about mid-scale or as the manual recommends.
  3. Bring the coil near the circuit. Hold the coil close to the coil or the loop of the circuit under test. For a first try, use close coupling to find the dip, and then move away.
  4. Turn the dial slowly. Sweep through the range. A good dip is sharp, and it is easy to pass over it if you turn quickly.
  5. Reduce the coupling. When you have found a dip, move the instrument away until the dip is only just visible. The reading at loose coupling is the most accurate, because close coupling pulls the oscillator frequency and shifts the dip.
  6. Read the frequency. Note the dial reading. For better accuracy, listen to the oscillator on a receiver, or use a frequency counter, and read the exact frequency from there.
  7. Check the harmonics. If the dial reading does not make sense, the dip may be at a harmonic of the oscillator or at a different resonance of the circuit. Check with another coil or compare with the calculation.

Reading the Result Correctly

The dial of an old dip meter is not precise. Its calibration may be off by a few percent, and the drift between uses can be noticeable. For work where a few percent is enough, such as finding the resonance of a trap to within the band, the reading is good. For a tighter result, check the oscillator frequency against a receiver, which is easy because the oscillator radiates a small signal, and apply the correction. The article on calibrating a transceiver against a time signal gives a method that you can use to check the dial of the receiver itself. A frequency counter or a software-defined receiver gives the exact value in one step.

It also helps to know what a dip looks like. A sharp, deep dip means a high-Q circuit that you are coupled to correctly. A shallow, wide dip means a lossy circuit, such as a trap with a lossy coil, or too loose a coupling. No dip at all can mean a wrong coil range, no coupling, or a circuit that is not resonant in the range you are searching.

Using a Dip Meter on an Antenna

To check a dipole with a dip meter, disconnect the feedline and join the two halves at the feedpoint with a small loop of wire, a turn or two, that you can couple to. Bring the coil of the dip meter close to the loop, and sweep. The dip gives the resonant frequency of the antenna, including the loop, which adds a little inductance, so the reading is slightly low. This is a good way to trim a new antenna to the band before you raise it, or to check one at the end of a feedline that you do not want to disturb. The guide to cutting and trimming a dipole gives the starting length, and the dip meter confirms where it ended. Work near the ground, where you can reach the feedpoint, since the height changes the resonance and the final tuning must be done in place with an SWR measurement.

For a vertical or a long wire, a dip meter can still find the resonances, but coupling to the antenna is harder, and the result depends on the ground and surroundings. Do not expect the same accuracy as for a trap on the bench.

Dip Meter or NanoVNA?

Modern vector network analysers, such as the NanoVNA, can measure impedance and resonance directly, as the guide to the NanoVNA explains. They show the SWR curve for an antenna, and they measure the impedance of a component or the length of a stub more precisely than a dip meter. In most cases an analyser is the better tool for an antenna that is connected to a feedline. The dip meter keeps its place for specific jobs.

TaskDip meterNanoVNA or analyser
Resonance of an unpowered trapGood, easy and quickPossible, needs a test fixture
Inductance of an unknown coilGood with a known capacitorDirect measurement
SWR curve of an antennaNot possibleThe right tool
Checking a transmitter for radiationPossible as a wavemeterNot suitable
Accuracy of frequencyA few percent without a checkHigh
CostLow, often found second-handLow to moderate

The dip meter remains useful because it couples without wires, so you can measure a circuit that has no connector, in place, and because it is robust and simple. For a station that already owns an analyser, a dip meter is not essential, but for the homebrew builder it is a cheap and rewarding instrument. See the guide to test equipment essentials for how it fits with a multimeter and a wattmeter.

Common Mistakes

  • Coupling too tightly. The dip is pulled to a lower frequency and the reading is wrong. Always check at the loosest coupling that still shows a dip.
  • Measuring a live circuit. Power and signals in the circuit upset the reading, and a high voltage is a danger. Measure circuits that are disconnected and discharged.
  • Using the wrong coil. A coil outside its range gives no dip or a false one. Match the coil to the frequency.
  • Mistaking a harmonic. The oscillator produces harmonics, and a dip at the second harmonic looks like a resonance at twice the true frequency. Check with another coil.
  • Trusting the dial. Verify the oscillator frequency with a receiver or a counter if the result matters.
  • Hand effect. Your hand near the coil or the circuit changes the frequency. Hold the tool by its case and keep the hand away from the tuned parts.

A Few Practical Tips From the Bench

Keep a notebook beside the instrument. Write down the coil you used, the dial reading and the result for each measurement, and your own correction against a receiver. After a few sessions you will know how the particular instrument behaves, and your corrections will make it more accurate than its dial suggests. When you test traps, measure both traps of a pair and compare them: a trap that differs by a few percent from its twin will give a lopsided dipole. When you measure a coil, keep the leads of the test capacitor short, since long leads add inductance and change the answer. Finally, remember the safety side. A trap hanging at the end of a wire can carry a high voltage when the antenna is used with power, so a dip measurement on the bench should be made before the trap is installed and not afterwards, when it is on the air.

Buying or Building a Dip Meter

Old tube-type dip meters are easy to find at hamfests and second-hand, and many are still in good order. Check that the oscillator runs, that the meter moves and that the coils are complete, since a missing coil limits the range. Solid-state versions, made by several manufacturers, are lighter and more stable, and they do not need a warm-up. Some builders make a dip meter from a few parts: an oscillator, a diode and a meter. It is a good first project, since it teaches the principle of resonance and can be calibrated against a receiver. Whatever you choose, keep the set of coils together and note the frequency range of each one on a label.

The Bottom Line

A grid dip meter is a tunable oscillator that shows a dip on its meter when it is tuned to the resonant frequency of a nearby circuit. It finds the resonance of traps, coils, stubs and antennas without wires and without power in the circuit, serves as an absorption wavemeter and as a rough signal source. Use the right coil, couple loosely, sweep slowly and verify the frequency with a receiver when it matters. A NanoVNA does many of the same jobs more precisely, but the dip meter is still a cheap, simple and instructive instrument for the bench of any radio amateur who builds and tunes antennas.

Frequently Asked Questions

What does a grid dip meter measure?

The resonant frequency of a tuned circuit, such as a trap, a coil with a capacitor, a coax stub or an antenna, by showing a dip in the meter when the oscillator matches that frequency.

Why is it called a grid dip meter?

In the original tube versions, the meter showed the grid current of the oscillator tube, which dipped at resonance. Solid-state versions keep the name even though they have no grid.

How accurate is a dip meter?

The dial is usually accurate to a few percent. For better accuracy, check the oscillator frequency with a receiver or a frequency counter while the dip is shown.

Can I use a dip meter on a live circuit?

No. It is designed for circuits that are not powered. A live circuit upsets the reading and may be dangerous. Disconnect and discharge the circuit first.

Is a dip meter still useful with a NanoVNA?

Yes, for unpowered traps, coils and for use as a wavemeter. A NanoVNA is better for SWR and impedance of an antenna on its feedline.

How do I avoid the pulling of the frequency?

Reduce the coupling until the dip is barely visible. Tight coupling shifts the oscillator frequency and gives a reading that is lower than the true value.


By the team behind LY4A

More tools from our team

LY4A is made by Internet Solutions. Try the rest of our products — each one saves you time in a different way.

internet-solutions.net ↗
Social media auto-posting PostRSS New posts from your RSS feed go to Facebook, X, LinkedIn, Telegram and 60+ more networks automatically. For clubs: DX news and club bulletins straight to Facebook and Telegram Free plan · since 2014 AI live chat for websites Talkmio Your website answers visitors 24/7 from your own content, in their language. For ham shops and clubs: questions answered 24/7, even during a contest Free plan · no card needed AI assistant Ask Mio Chat, code, design, writing and research. Mio picks the best model for each task. Antenna maths, QSL card designs, contest rules explained in plain words Free plan AI blog & social autopilot AI Blog Autopilot AI writes 2,000–3,000-word SEO articles and shares each one to 58+ social networks. For club websites: regular articles written for you and shared to social networks First 3 articles free Website health check Site AI Audit SEO, speed, SSL, security and e-mail setup in one report, ranked by what to fix first. Check your club or DXpedition website for free First audit free Deep SEO crawl Site SEO AI Audit A full SEO crawl across 7 areas, including AI search visibility, with fixes ranked by impact. See why your club site is not found on Google — and how to fix it First audit free RSS & product feeds RSS Feed Creator Create RSS from any web page, plus product feeds for Google and Meta that update themselves. Follow DXpedition and club pages that have no RSS Free plan Web development & SEO Internet Solutions Websites, e-shops and custom systems, designed, built and run by our team. Club websites, DXpedition pages, log search and QSL systems Since 2011