Bobtail Curtain Antenna: Three Verticals for Low-Band DX

Bobtail Curtain Antenna: Three Verticals for Low-Band DX

On the low bands, a vertical is the natural DX antenna, because it radiates at a low angle. Its weakness is that it has no gain and no direction. The bobtail curtain antenna keeps the low angle and adds both. It is made of three vertical wires, a quarter wavelength tall, joined at the top by a horizontal wire a full wavelength long and fed at the bottom of the middle wire. Because the three verticals are phased, the signal is concentrated at right angles to the wire plane, and a good installation gives several decibels over a single vertical. The antenna is made of wire, needs one or two supports and no rotator, and it has been a favourite on 80 and 40 metres for a long time. This guide explains the structure, the sizes, the matching and the practical points that decide whether it works.

How the Bobtail Curtain Works

The antenna is a form of curtain array. Three vertical quarter-wave radiators stand in a row, spaced a half wavelength apart. The tops of the three are connected by a horizontal wire, which makes the total length of the top one wavelength. The current flows up in the centre vertical, spreads along the horizontal wire to the two outer verticals and flows down in them. The geometry makes the current in all three verticals flow in the same direction at the same time, so the three radiate in phase. Because they are half a wavelength apart, the signals add at right angles to the line of the antenna, and they cancel along the line. The result is a bidirectional pattern, broadside to the wire, with a narrow main lobe in the horizontal plane and nulls off the ends.

The horizontal wire does not radiate much, since the currents in its two halves are in opposite directions and cancel in the far field, so the radiation is mainly vertically polarised, with the low angle of a vertical. This is the main reason for building it: the antenna radiates a vertically polarised signal at a low angle, with gain. The usual figure quoted for a well-made bobtail curtain is a gain of several decibels over a single quarter-wave vertical over the same ground, with a horizontal beamwidth that is roughly 80 to 90 degrees. The exact gain depends on the ground and on the radial system, so treat it as an approximate value.

Dimensions for the Popular Bands

The wire lengths follow from the wavelength. A half-wave in wire is about 143 divided by the frequency in megahertz, in metres. The quarter-wave verticals are half of that, and the horizontal wire is two half-waves long. The table gives approximate values for a frequency in the middle of each band. They are starting points, and the lengths are adjusted when you measure the antenna.

BandFrequencyVertical wire heightTop wire lengthSpacing of verticals
160 m1.83 MHzabout 39 mabout 156 mabout 78 m
80 m3.6 MHzabout 20 mabout 79 mabout 40 m
40 m7.1 MHzabout 10 mabout 40 mabout 20 m
30 m10.12 MHzabout 7 mabout 28 mabout 14 m
20 m14.15 MHzabout 5 mabout 20 mabout 10 m

The figures show why the bobtail curtain is most practical from 40 metres upwards. On 40 metres the antenna is 40 metres wide and 10 metres tall, which a big garden or a field with three posts or masts can hold. On 80 metres it needs a field of 80 metres and verticals that are 20 metres tall, so the antenna is a project for a country property. On 160 metres, the size is beyond most stations. The top wire can be supported by the outer masts, with the vertical wires hanging down from it, and the horizontal wire keeps the structure compact in height compared with a full-size 80 metre array.

How the Antenna Is Built

The structure uses two outer supports and a centre support, or two supports and a catenary of the top wire. The top wire, one wavelength long, is stretched between the outer supports at the top, and the three vertical wires hang down from it at the centre and at the two ends of the top wire, so that the verticals are a half wavelength from each other. The outer verticals end in the air, a short distance above the ground, where they are insulated. They are not connected to ground, and they act as the radiating wires, and the horizontal wire acts as the phasing line. The centre vertical is fed at its lower end, where the feedline connects between the bottom of the wire and a ground system.

The wires are of copper or copper-clad steel, and they need to be strong enough to carry their own weight and the wind. Keep the verticals straight and vertical, since a tilt changes the phase. Use insulators at the ends of the top wire and at the bottoms of the outer verticals. The structure needs rope, pulleys and a way to lower the wires for adjustment. If the supports are of different heights, keep the top wire as level as you can, since a sloping wire changes the balance of the currents.

Feeding and Matching

The feed point at the bottom of the centre wire is a point of high impedance. A single quarter-wave vertical has a low impedance of about 36 ohms at its base, but in the bobtail curtain the base of the centre wire is a high-impedance point, since the current distribution of the three verticals together makes the voltage at the bottom much higher than the current. The value depends on the design and on the ground, and in practice it is high enough to need a matching network. The usual solution is a tuned circuit, built from a coil and a variable capacitor, at the base of the centre wire. This is a parallel resonant network that is tuned for minimum SWR, and it is an example of impedance matching. The network is placed in a weatherproof box at the bottom of the wire, with a link coil or a tap that connects to the coax. Alternatively, a transformer of the right ratio can be used where the impedance is known.

Because the matching network is critical, it is best to measure the impedance of your antenna with an analyser, and then to design the matching network. A NanoVNA or similar instrument at the feedpoint tells you the resistance and the reactance, and the matching can be adjusted until the SWR is low. The tuned circuit has a narrow bandwidth, which means that on 80 metres you may need to retune for the CW and the SSB parts of the band, and a remote-controlled capacitor is one way to do it from the shack.

The Ground System

As with every vertical, the performance depends on the ground. The bobtail curtain is excited at the bottom of the centre wire, which needs a return path. A system of radials, laid on or just below the ground, under and around the centre wire gives the current a path and reduces the losses. The guide to vertical antenna radials describes how many radials and what length work best. For a quarter-wave vertical on 80 metres, a minimum of 16 radials of a quarter wavelength each is a good target, and more is better. The outer verticals are not grounded, so they do not need their own radials, although a small number of radials near them can reduce the coupling to the ground and improve the symmetry.

Where the Bobtail Is Used

The antenna is a good choice for operators who want DX from a vertically polarised, low-angle antenna with a modest directivity and who have a field. Its broadside lobes point both ways, so a station can orient the wire to favour two regions of the world. A station in Europe with a north-south wire points east and west, towards Asia and North America. It is also used as a receiving and transmitting antenna on 160 and 80 metres, where low noise from the direction off the ends can be an advantage. The article on receive antennas for the low bands explains the importance of separate receiving antennas, since a bobtail with nulls off the ends can reduce a noise source in that direction, and the guide on atmospheric noise on the low bands describes the noise that limits low-band reception.

Bobtail Curtain Compared With Other Low-Band Antennas

A single vertical is the simplest low-angle antenna but has no gain. A four-square vertical array gives gain and switchable directions, and it needs four verticals and a phasing box. A half-square antenna is a lighter solution for 40 and 80 metres, made of two verticals joined by a horizontal wire, and the bobtail curtain is its larger relative with three verticals and more gain. An inverted L is the choice for a small plot and a good start on 160 and 80 metres. If you have the space and want a fixed gain antenna for 80 or 40 metres, the bobtail curtain is one of the most effective wire options, and it can be built without a tower or a rotator.

Common Problems

  • Poor ground. A weak radial system wastes power in the ground. Add radials before trying other cures.
  • Unequal verticals. If the outer wires are not the same length, the currents are not in phase and the pattern is distorted. Measure each wire.
  • Wrong spacing. A top wire that is too short or too long shifts the phases. Keep the spacing close to a half wavelength.
  • Matching network losses. A coil with a low Q wastes power. Use a good coil and a well-made capacitor.
  • Nearby metal. Fences, power lines and buildings distort the pattern and detune the antenna. Keep the antenna in the clear.
  • Safety. The voltage at the base of the centre wire can be high. Enclose the matching network, and keep people and animals away.

A Simple Test Plan

First, build the antenna for the band that you use most and install the radials. Second, measure the resonance with an analyser at the feed point and trim the lengths so that the resonance is near the middle of the band. Third, adjust the matching network until the SWR is low at the feed. Fourth, compare the antenna with your usual one. Use a recorded session, or reports from the same stations, at the same time on the two antennas, and note the difference in signal strength. Fifth, test the pattern: ask a station to the side and a station off the end to report, and see how the signals differ. The directional effect is the proof that the three verticals are in phase. If the lobes are not clear, check the equal length of the verticals and the symmetry of the structure.

The Bottom Line

The bobtail curtain antenna is a wire array of three quarter-wave verticals joined at the top by a half-wave-per-section horizontal wire, one wavelength long in all, and fed at the bottom of the centre vertical. It gives low-angle vertical polarisation with several decibels of gain and a bidirectional broadside pattern, for the cost of wire, rope and a matching network. It suits 40 and 80 metres where a field is available, and it asks for a good radial system, equal wire lengths and a well-made tuned matching circuit. For the station that wants a fixed, low-angle gain antenna for the low bands, it is a design that has worked for many decades.

Frequently Asked Questions

How much gain does a bobtail curtain have?

Several decibels over a single quarter-wave vertical on the same ground, with a bidirectional pattern. The exact figure depends on the ground and the radials, so treat the quoted values as approximate.

Why is it called a bobtail curtain?

It is a curtain array, a row of vertical wires hanging from a horizontal wire, and bobtail refers to the short, truncated form with only three vertical wires.

Which direction does it radiate?

Broadside to the wire, in two opposite directions. Along the line of the wire there are deep nulls, so decide the orientation before you build.

Does the bobtail curtain need radials?

Yes. The centre wire is fed against ground, so a good radial system under it is essential for efficiency, as for any vertical.

Can I use it on more than one band?

It is designed for one band. On other bands the current distribution and the pattern change, so a multiband use needs modelling and a different matching.

Is the bobtail curtain good for a small garden?

Only on the higher bands. On 40 metres it is about 40 metres wide, and on 80 metres twice that, so small plots should look at a half-square or an inverted L.


By the team behind LY4A

More tools from our team

LY4A is made by Internet Solutions. Try the rest of our products — each one saves you time in a different way.

internet-solutions.net ↗
Social media auto-posting PostRSS New posts from your RSS feed go to Facebook, X, LinkedIn, Telegram and 60+ more networks automatically. For clubs: DX news and club bulletins straight to Facebook and Telegram Free plan · since 2014 AI live chat for websites Talkmio Your website answers visitors 24/7 from your own content, in their language. For ham shops and clubs: questions answered 24/7, even during a contest Free plan · no card needed AI assistant Ask Mio Chat, code, design, writing and research. Mio picks the best model for each task. Antenna maths, QSL card designs, contest rules explained in plain words Free plan AI blog & social autopilot AI Blog Autopilot AI writes 2,000–3,000-word SEO articles and shares each one to 58+ social networks. For club websites: regular articles written for you and shared to social networks First 3 articles free Website health check Site AI Audit SEO, speed, SSL, security and e-mail setup in one report, ranked by what to fix first. Check your club or DXpedition website for free First audit free Deep SEO crawl Site SEO AI Audit A full SEO crawl across 7 areas, including AI search visibility, with fixes ranked by impact. See why your club site is not found on Google — and how to fix it First audit free RSS & product feeds RSS Feed Creator Create RSS from any web page, plus product feeds for Google and Meta that update themselves. Follow DXpedition and club pages that have no RSS Free plan Web development & SEO Internet Solutions Websites, e-shops and custom systems, designed, built and run by our team. Club websites, DXpedition pages, log search and QSL systems Since 2011