Low Power Contesting: How to Score Well With 100 W or QRP

Low Power Contesting: How to Score Well With 100 W or QRP

Walk into a contest weekend with a 100-watt radio and a wire antenna, and it is easy to feel outgunned. The big stations run a kilowatt into towers of beams, and their signals shake the band. Yet every contest has a low power category, and some of the best-loved results in the hobby come from stations that compete in it. The category exists precisely so that you compare yourself with others who run the same power. Low power contesting is a skill of its own: it rewards listening, antenna work, good timing and clear thinking more than raw output. This guide explains what low power really costs in decibels, how the categories are defined, which strategies fit a small signal and how to build a plan for a weekend, whether you run 100 watts or 5 watts.

Categories and Limits

Contests define power classes by the output power of the transmitter. Typical definitions are a high power class with up to the legal limit, a low power class with up to 100 watts in many contests and 150 watts in some, and a QRP class with up to 5 watts. The rules of each contest give the exact limits, so check them, including whether the class is also split by mode or by operator assistance. The article on contest categories explains the other divisions, and the principle is that you compete in your own class, so a 100-watt entry is compared with other 100-watt entries and not with a kilowatt station. For general background, see the overview of contesting.

What Low Power Really Costs

The cost of lower power is smaller than it feels. Radio signal strength is measured in decibels, and an S-unit is about 6 decibels. The difference between 100 watts and 1,500 watts is a power ratio of 15, which is 11.8 decibels, or about two S-units. A 100-watt station is therefore two S-units weaker than a legal-limit station with the same antenna, which is a clear difference but not a wall. A QRP station at 5 watts is 13 decibels weaker than 100 watts, and about 25 decibels weaker than a kilowatt, or four S-units. The same numbers show that a good antenna matters as much: a beam with 8 decibels of gain more than a dipole does the work of a sixfold increase in power.

PowerDifference from 1,500 WAbout how many S-units
1,500 W0 dB0
100 W11.8 dB weakerabout 2
25 W17.8 dB weakerabout 3
5 W (QRP)24.8 dB weakerabout 4
1 W31.8 dB weakerabout 5

The figures give an idea of why QRP is harder but not impossible: at 5 watts you are four S-units down, and a mode with a narrow bandwidth can recover several of them. The article on decibels explains the arithmetic of S-units and gains.

Strategy 1: Search and Pounce First

The big stations run: they hold a frequency, call CQ and let the callers come to them. With a smaller signal, holding a frequency is harder, since stations farther away will not hear you in the noise of the band. Search and pounce, tuning across the band and calling the stations that you hear, is the natural method of a low power station. A strong station will hear your call, and the loud stations are the ones you can work. This is how a low power operator collects most of the multipliers and many of the points. The article on run or search and pounce explains the balance and the ways to improve the rate. A good low power rate in a pounce session is often 40 to 80 contacts an hour on the busy bands, with the right timing.

That does not mean that you should never run. At times when a band is open to a large population and the competition is thin, such as the early hours on the low bands in a DX contest, a low power station can hold a frequency and call CQ, and a few callers will answer. Short runs, tried when the band has no one else, add contacts without fighting the loudest signals. Test it for a few minutes and return to searching if the rate is poor.

Strategy 2: Antennas Beat Amplifiers

The cheapest decibels are in the antenna. An improvement of 3 decibels in the antenna is the same as doubling the power. Raising a dipole from low to half a wavelength high, reducing the loss in the feedline, adding a second element or making a better ground system for a vertical are all more effective than moving from 100 to 200 watts. Receive antennas count as well: a quieter receive antenna lets you hear weaker stations, which doubles the usefulness of the transmit gain, as the article on low-band receive antennas shows. Check the SWR and the feedline loss before the contest, and use the checklist in the article on the contest station checklist.

Strategy 3: Choose the Mode Wisely

CW is the low power operator’s friend. A CW signal occupies a narrow bandwidth, a receiver with a filter of 300 or 500 hertz rejects most of the noise and the interference, and a signal that is unreadable on SSB can be copied by ear in CW. Compared with SSB, the effective gain of CW is often put at 10 decibels or more, as a combination of the narrow bandwidth and the efficient use of power. A QRP station on CW can therefore do better than a 100-watt station on SSB. Digital modes in contests, such as RTTY, offer similar advantages. If you can send and receive CW at 25 to 30 words per minute, a CW contest is the best way to use a low power station. If you do not, learn: the article on QRP operating shows how far a small signal can go.

Strategy 4: Be Where the Signals Are, When They Are

Timing and band choice substitute for power. Work the band that is open to the largest number of stations at the time. In a worldwide contest, that means 20 metres in the morning, 15 and 10 metres in the afternoon when they are open, and 40 and 80 metres in the evening and night. Use sunrise and sunset to your advantage, because the grey line gives a boost on the low bands. The article on band change strategy describes how to plan the changes. A low power station that moves to the right band at the right time can match the points of a stronger station that stays in the wrong place.

Strategy 5: Work Smarter, Not Louder

  • Use the right exchange speed. Send your callsign and the exchange once, clearly, at the speed that the other station uses, and do not repeat unless asked.
  • Call at the right moment. In a pile of callers, find the gap and send your call once. A call on top of others is wasted.
  • Work the strong stations first. They give quick contacts and the multipliers are often among them.
  • Use the call history and Super Check Partial. They help you copy weak calls from a partial and avoid busted contacts, as the article on Super Check Partial explains.
  • Do not give up on a station too early. A weak station may be copied on the second or third call, and a strong station can be called a second time with a slightly different frequency.
  • Rest. A good result needs a good operator, and fatigue costs more points than a few decibels. Plan your sleep and breaks.

Preparing the Station

A low power station has little margin for faults, so preparation counts for more. Test every band that you plan to use with the antenna and measure the SWR across the contest segments, because a mismatch of 2 to 1 costs a small but real part of a small signal. Check the feedline for loss, particularly on the higher bands, since 3 decibels lost in the coax is half of your power gone. Use a short, good-quality cable and keep the connectors clean. Set the transmitter audio or keying carefully: a clean 100 watts is better than a splattering 100 watts, and a transmitter that is slightly over-driven spreads its energy outside its channel. Make sure that the logging software, the keyer and the radio control are working together, with function-key messages prepared, so that no seconds are lost to typing. A mistake in the setup costs more contacts than a lack of power does.

Listening Is Half the Contest

With a small signal, the ability to hear weak stations becomes your main asset, because the stations that you can hear are the ones that may hear you. Use a narrow filter in CW, a gentle noise reduction and, where the noise is a problem, the receive antenna or a loop that has a better signal-to-noise ratio than the transmit antenna. Keep the AGC set so that a strong neighbour does not suppress the weak signal you are copying. Many experienced low power operators say that they win the points on the receive side: they copy the calls of weak stations on the first pass, while others ask for repeats. Practice with a pileup simulator such as the one in the article on Morse Runner to train your ear for weak, overlapping calls.

A Sample Plan for a Worldwide Weekend

Suppose a 100-watt station with a dipole and a vertical enters a 48-hour DX contest in CW. On the first morning, it starts on 20 metres and pounces on the strong stations, collecting multipliers. By midday, 15 metres opens to some regions, and the station moves there for an hour of easy contacts. In the afternoon, it returns to 20 metres and, when the rate is quiet, makes short runs on a clear frequency. As the evening comes, it changes to 40 metres, where signals are strong, and works the stations that call, then to 80 metres for the sunrise at the other end. It sleeps for four hours in the quiet middle of the night and returns for the morning openings of the second day. A plan like this, written in advance, means that every hour has a purpose, and the low power class is won by consistent work over two days rather than by a single peak.

Setting Goals for a Low Power Weekend

Set a goal that is realistic. Compare your result with the logs of earlier years in your class, which sponsors publish. If you made 200 contacts last time, aim for 250. Choose the multipliers that you will target, for example a specific number of countries or zones. Decide in advance which bands you will use at which hours, and write the plan on a card. After the contest, look at your rate sheet and your missed multipliers, as the article on log analysis shows, and set the next goal from the findings. Progress in low power contesting comes from many small improvements: a better antenna, a faster exchange, a cleaner log.

The Bottom Line

Low power contesting is a fair fight in its own class. A 100-watt signal is only about two S-units weaker than a kilowatt, and QRP at 5 watts about four, and the difference can be recovered with a better antenna, CW, good timing and a clear plan. Use search and pounce as the main method, with short runs when the band is quiet. Spend effort on the antenna and the receive side, choose the band that is open to the most stations, keep the exchange short and the log clean, and rest. A well-run low power entry can finish high in its class and enjoy the weekend more than a loud one.

Frequently Asked Questions

How much weaker is a 100 W signal than a kilowatt?

About 10 to 12 decibels, depending on the exact power, which is roughly two S-units. A good antenna can make up much of that.

Can QRP stations do well in contests?

Yes, especially in CW, in the QRP class where all entries run 5 watts or less. Careful timing and antenna work help a great deal.

Should a low power station run or search and pounce?

Mostly search and pounce, since it uses the strong stations you can hear. Try short runs when the band is open and quiet.

Is CW better for low power contesting?

Generally yes. A narrow filter and efficient use of power make CW the strongest mode for a small signal.

What is better: more power or a better antenna?

A better antenna, usually. Every 3 dB of antenna gain is like doubling the power and it helps receiving as well.

How do I know the power limits of a contest?

Read the rules of the contest. Common limits are 100 or 150 watts for low power and 5 watts for QRP, and the definitions can differ.


By the team behind LY4A

More tools from our team

LY4A is made by Internet Solutions. Try the rest of our products — each one saves you time in a different way.

internet-solutions.net ↗
Social media auto-posting PostRSS New posts from your RSS feed go to Facebook, X, LinkedIn, Telegram and 60+ more networks automatically. For clubs: DX news and club bulletins straight to Facebook and Telegram Free plan · since 2014 AI live chat for websites Talkmio Your website answers visitors 24/7 from your own content, in their language. For ham shops and clubs: questions answered 24/7, even during a contest Free plan · no card needed AI assistant Ask Mio Chat, code, design, writing and research. Mio picks the best model for each task. Antenna maths, QSL card designs, contest rules explained in plain words Free plan AI blog & social autopilot AI Blog Autopilot AI writes 2,000–3,000-word SEO articles and shares each one to 58+ social networks. For club websites: regular articles written for you and shared to social networks First 3 articles free Website health check Site AI Audit SEO, speed, SSL, security and e-mail setup in one report, ranked by what to fix first. Check your club or DXpedition website for free First audit free Deep SEO crawl Site SEO AI Audit A full SEO crawl across 7 areas, including AI search visibility, with fixes ranked by impact. See why your club site is not found on Google — and how to fix it First audit free RSS & product feeds RSS Feed Creator Create RSS from any web page, plus product feeds for Google and Meta that update themselves. Follow DXpedition and club pages that have no RSS Free plan Web development & SEO Internet Solutions Websites, e-shops and custom systems, designed, built and run by our team. Club websites, DXpedition pages, log search and QSL systems Since 2011