HB9CV Antenna: A Compact Two-Element Phased Beam for VHF and 10 m

Some antennas are famous because they are large, and some because they achieve a great deal with very little. The HB9CV antenna belongs to the second group. It has only two elements and a short boom, yet it delivers more gain and a better front-to-back ratio than a two-element Yagi, and often about as much gain as a three-element one. It is light enough for a hand-held fox hunt, small enough for a balcony mast on 10 metres and simple enough to build in an afternoon. The secret is not extra elements but the way the two elements are fed. This guide explains the principle, compares the HB9CV with the Yagi and the Moxon, gives typical dimensions and describes how to build, match and use one on the bands where it shines.
The Idea: Two Driven Elements
In a Yagi, only one element is connected to the transmitter, and the others, the reflector and the directors, work by induction. The HB9CV takes a different path. Both elements are driven, and they are fed in such a way that the currents in them differ in phase by about 180 degrees. Its name comes from the callsign of its Swiss designer. A short length of wire or tubing between the two elements, called the phasing line, connects them and provides the necessary phase shift, together with the physical spacing between the elements. The result is a phased array in a very small package.
The spacing is much smaller than in an ordinary Yagi, only about one eighth of a wavelength. With the phase shift that the phasing line provides, the radiation from the two elements adds in the forward direction and cancels to the rear. The principle is the one in the article on broadside and end-fire arrays: two sources spaced by a fraction of a wavelength and fed with a phase difference form a directional pattern, and with the right combination the pattern has a strong forward lobe and a deep null behind it.
How the Phasing Works in Practice
It helps to follow a wave through the antenna. The transmitter’s current flows into the feed point on the phasing line and divides between the two elements. One element receives it directly, and the other receives it through the crossed section of the line, which reverses its sign and adds a further delay. When the radio wave leaves the two elements, the wave from the rear element has to travel an extra eighth of a wavelength to reach the front, and this path difference adds another delay. The sum of the electrical delay in the line and the delay in the air is arranged so that in the forward direction the two waves arrive in step and reinforce each other. In the backward direction, the delays add up the other way, and the two waves meet in opposition and cancel. The depth of the cancellation depends on how close the amplitudes and phases are to the ideal, which is why the build must be careful.
The same arrangement also explains why the antenna is sensitive to what lies near it. A metal object close to one element changes its current and spoils the balance. On a boom of metal, the elements must be isolated from it or the dimensions must be corrected. Keep the boom, the mast and the cable at right angles to the elements, and keep the coax away from the phasing line.
Performance in Numbers
The figures vary with the design and the quality of the build, but the typical picture is clear. The gain of an HB9CV is about 4 to 5 decibels over a dipole, which is roughly one decibel more than a good two-element Yagi and about the same as a short three-element Yagi. The front-to-back ratio is high, commonly 20 decibels or better when well tuned, compared with 10 to 15 decibels for a two-element Yagi optimised for gain. The beamwidth is wide, about 60 to 70 degrees in the horizontal plane, which is an advantage in a portable or mobile setting because aiming does not have to be precise. The pattern, compared with the others, is described in the article on the radiation pattern.
| Property | HB9CV | Two-element Yagi | Moxon |
|---|---|---|---|
| Elements | 2, both driven | 2, one driven | 2 folded, one driven |
| Typical gain over a dipole | 4 to 5 dB | 3 to 4 dB | about 3 to 4 dB |
| Front-to-back ratio | 20 dB or more | 10 to 15 dB | 25 dB or more |
| Boom length | About 0.12 wavelength | About 0.15 to 0.2 wavelength | About 0.1 wavelength |
| Feed impedance | Needs a matching network | Low, needs a match | About 50 ohms |
| Bandwidth | Moderate | Moderate | Good |
The Moxon, described in the article on the Moxon antenna, shares the HB9CV’s small size and good front-to-back ratio, but achieves it by bending the element tips, whereas the HB9CV uses a phasing line. Neither is better in all respects. The Moxon feeds directly at 50 ohms, and the HB9CV gives slightly more forward gain.
Typical Dimensions
The dimensions below are typical starting values and they are no substitute for a published design with the exact diameter of tubing. For a design at 144.2 MHz, where a wavelength is 2.08 metres, the elements are each a little over half a wavelength long, about 1.0 to 1.05 metres, with the front element slightly shorter than the rear one. The spacing between them is about one eighth of a wavelength, roughly 26 centimetres. The phasing line is made of wire or rod, and its length, together with the way it crosses between the two elements, sets the phase. The matching section, often a gamma match or a short stub near the feed point, brings the impedance to 50 ohms.
- Element length: about 0.48 to 0.5 wavelength, with a small difference between front and rear.
- Spacing: about 0.125 wavelength between the two elements.
- Phasing line: a conductor that crosses from one element to the other, forming a transposed connection that produces the phase shift.
- Feed point: on the phasing line, a short distance from the centre, using a gamma or a tap for matching.
At 10 metres the same antenna has elements about 5 metres long and a boom of about 3.5 metres, which is large but within the reach of a garden mast. At 6 metres it is more modest, and on 70 cm it fits in a hand.
Building One
The mechanical construction is simple, and the electrical details are the ones that matter. A boom of aluminium or wood carries two elements of aluminium tube or rod. In the classic form, the elements are isolated from the boom, and the phasing line, a thinner rod or a wire, runs from the centre of one element to the centre of the other, usually crossed so that the connection reverses the phase. The coax is attached at a point on the phasing line. The shield is connected to one element and the centre conductor to the other, with the matching section between, and a choke balun on the coax prevents current on the outside of the cable, as described in the article on baluns and ununs.
Use clean, tight, corrosion-resistant joints, especially at the phasing line and the feed, because the antenna is a resonant structure and a poor joint raises the losses and shifts the tuning. For a portable version, a tape-measure antenna or a rod design in the style of the handheld Yagi can be assembled in seconds and carried in a bag.
A Parts List for a 144 MHz Version
A simple version for two metres can be built with materials from a hardware store. You need a boom of dry wood or plastic tube about 40 centimetres long, two lengths of aluminium rod or tube of 6 to 8 millimetres diameter for the elements, a piece of stiff copper wire or rod for the phasing line, two insulated mounting blocks or clamps for the elements, a connector socket of the type you prefer and a few centimetres of coax for a choke balun. Add stainless screws, heat-shrink tubing and a tube of weatherproof sealant for the joints. Cut the elements slightly long and trim them while measuring with an analyzer, since it is easier to remove metal than to add it. Photograph each stage, because the crossed phasing line is the part that people most often assemble wrongly, and a mistake there turns a beam into a poor antenna that has a null in the wrong place.
Matching and Tuning
With a SWR meter or an antenna analyzer, check the match across the band. The usual adjustment is the position of the feed point or the gamma shorting bar. Move it a little at a time and check the SWR, as you would with a Yagi, and see the article on the NanoVNA for the technique of sweeping. The target for a first build is an SWR below 1.5 across the part of the band you use. The pattern is less sensitive to small tuning errors than the match is. Do the tuning with the antenna at its working height and away from large metal objects, since the nearby ground and mast change the result.
Where the HB9CV Shines
- Fox hunting. The wide beam and the high front-to-back ratio make it a good direction-finding antenna in light and compact form, as the guide to ARDF and the overview of radio direction finding explain. The null behind the antenna can be used to reject an unwanted signal.
- Portable and mobile VHF and UHF. A small, light beam for 144 or 432 MHz, in the car, on a hill or in a tent, is an easy way to gain a few decibels.
- 10 and 6 metres. A rotatable two-element beam for the upper bands on a small tower or a lightweight mast gives gain and a rear null in a short boom.
- Limited space. Where a three-element Yagi will not fit, the HB9CV provides much the same gain.
- Interference rejection. A rear null of 20 decibels or more helps against a local noise source or a nearby transmitter behind the antenna.
Limits and Cautions
The HB9CV is not a universal answer. Its bandwidth is moderate, so a design for the SSB and CW part of 144 MHz may not cover the FM part with a low SWR. The gain of two elements is modest compared with a long Yagi, and for weak-signal work such as tropospheric scatter or meteor scatter, a longer beam is better. The phasing and matching add some complexity, and an error in the phasing line reduces the front-to-back ratio at once. Since the elements are driven, the antenna is sensitive to the balun and the feedline, and a common-mode current on the coax spoils the pattern. Finally, a published design is a safer start than a freehand one, because the lengths depend on the tube diameter and on the exact shape of the phasing line.
The Bottom Line
The HB9CV antenna feeds two elements, spaced about an eighth of a wavelength, in antiphase through a phasing line. It gives about 4 to 5 dB of gain over a dipole, a front-to-back ratio of 20 dB or more and a wide beam, in a very short boom. It is simple to build, light to carry and well matched to fox hunting, portable VHF and UHF, and compact beams for 10 and 6 metres. It needs a matching section and a balun, a precise build and a check with an analyzer. Choose it when space and weight are limited and a quiet rear matters, and choose a longer Yagi when you need the highest gain for weak-signal work.
Frequently Asked Questions
What does HB9CV mean?
It is the callsign of the Swiss amateur who designed the antenna. The name has become the standard name for this two-element phased beam.
How much gain does an HB9CV have?
Typically 4 to 5 dB over a dipole, about a decibel more than a two-element Yagi and similar to a short three-element Yagi.
Why is the front-to-back ratio so good?
The two driven elements are fed in antiphase, so the radiation from them adds in front and cancels behind the antenna.
Do I need a balun on an HB9CV?
Yes. The antenna is balanced and the coax is not, so a choke balun keeps current off the shield and protects the pattern.
Is the HB9CV better than a Moxon?
It gives a little more forward gain, while the Moxon is easier to feed at 50 ohms and has a wider bandwidth. Both are compact and have a good rear null.
Can I build an HB9CV for 10 metres?
Yes, though the elements are about 5 metres long. It works well on a small mast or tower where a larger Yagi would not fit.